Rain Garden Sizing Tool

Placeholder subtitle

A = (C × i × Ac × t) ÷ (d + f × t)
A  — rain garden area (m²)
C  — runoff coefficient (0.85)
i  — rainfall intensity (m/s)
Ac — contributing area (m²)
t  — storm duration (3 600 s)
d  — ponding depth (0.15 m)
f  — soil infiltration rate (m/s)
Contributing area
Soil & infiltration type

Infiltration rate: f = 5×10⁻⁶ m/s

Storm return period

Placeholder assumptions note

Rain garden area — CIRIA C753
— m²
minimum surface area at 150 mm ponding depth

Storage volume: — m³   ·   Drain-down: — hrs after storm
Placeholder disclaimer

About this method

Placeholder paragraph 1

Placeholder paragraph 2

Placeholder paragraph 3 See how our Desktop Study + Site Visit works.

Rain garden sizing guide

A rain garden is a shallow, planted depression that receives runoff from a roof, paved area or other small catchment. It temporarily stores water, filters pollutants through its growing medium and, where the ground allows, infiltrates water into the soil.

What units does the calculator use?

Enter the contributing area in square metres (m²) or hectares (ha). Rainfall intensity is shown in millimetres per hour (mm/hr), while the equation converts it to metres per second (m/s). The result is a rain garden surface area in m²; storage volume is in cubic metres (m³), and drain-down is shown in hours.

When should I use a rain garden?

Use this calculator for early-stage sizing of infiltration-based SuDS serving a roof, courtyard, parking area or similar small catchment. It is most useful before detailed design, site testing and planning discussions. For a complete scheme, see our SuDS design consultancy and confirm infiltration, groundwater, utilities, exceedance routes and maintenance requirements on site.

Worked example: a community centre roof

A community centre is directing runoff from a 250 m² roof to a new rain garden. The early-stage assessment uses the calculator's standard runoff coefficient and a 1-in-30-year rainfall intensity.

Inputs

  • Contributing area: 250 m² of roof
  • Rainfall intensity: 50 mm/hr, converted to 1.39 × 10⁻⁵ m/s
  • Infiltration rate: 5 × 10⁻⁶ m/s (sandy clay / loam preset)
  • Fixed assumptions: C = 0.85, 60-minute storm and 150 mm ponding depth

Result: approximately 63.2 m² of rain garden area, 9.5 m³ of temporary storage and an estimated 8.3-hour drain-down time.

A 20% precautionary climate allowance would increase the indicative area to approximately 75.8 m². This is a screening example, not a construction design: confirm the infiltration rate with in-situ testing before relying on the result.

Rain garden and runoff FAQs

How do I calculate runoff?

For a simple runoff volume estimate, multiply runoff coefficient by rainfall depth and contributing area. For peak discharge from a small catchment, use the Rational Method Q = CiA, then compare the result with the capacity of the proposed SuDS. Our Runoff Calculator calculates peak flow using that method.

What is a greenfield runoff rate?

A greenfield runoff rate is the estimated peak discharge from a site in its undeveloped or natural condition. It is commonly used as a pre-development benchmark for drainage design; it requires site-specific catchment, rainfall and hydrological assumptions and is not produced by this simplified rain garden calculator.

What is a runoff coefficient?

A runoff coefficient, C, is the fraction of rainfall assumed to become runoff from a surface. A value near 1 represents a highly impermeable surface; a lower value represents greater interception and infiltration. This calculator uses C = 0.85 as a fixed early-stage assumption for typical hardstanding.

What is the Rational Method?

The Rational Method estimates peak runoff using Q = CiA: runoff coefficient (C) × rainfall intensity (i) × contributing area (A). It is useful for small, reasonably uniform catchments and early-stage drainage checks. It is different from this calculator's infiltration-based rain garden sizing method. Use the peak runoff calculator when you need a flow estimate.

What is a rain garden?

A rain garden is a shallow, planted SuDS feature that receives runoff from a roof, paved area or other small catchment. It temporarily stores and filters water, then allows it to infiltrate into the ground where site conditions are suitable. It is not intended to function as a permanent pond.

How big should a rain garden be?

The required area depends on the contributing area, rainfall intensity, runoff coefficient, soil infiltration rate, storm duration and ponding depth. Use this calculator for early-stage sizing, then confirm the result with site-specific infiltration testing and detailed drainage design.

What soil is suitable for a rain garden?

A rain garden needs a tested infiltration rate that allows water to drain within the required time. Sandy loam and similar free-draining soils may be suitable, while heavy clay can require a lined feature, underdrain or different SuDS component. Confirm the rate with in-situ testing rather than relying only on a soil map.

How long should a rain garden take to drain?

As an early-stage check, an infiltration-based rain garden should generally drain down within 48 hours of a design storm. Longer standing water can damage planting and create anaerobic conditions. The calculator provides an estimate, but the infiltration rate and final design must be verified on site.

Where should a rain garden be located?

Place it where runoff can reach it safely by gravity, while keeping clear of building foundations, buried services, contamination, unstable slopes and unsuitable groundwater conditions. The design should also provide access for maintenance and a safe route for exceedance flows.

Does a rain garden need an overflow?

Yes. A rain garden should have a defined overflow or exceedance route for storms larger than the design event or when infiltration is temporarily reduced. The route should direct water away from buildings, neighbouring land and unsafe areas without causing erosion or pollution.

Related tools & next steps